UNV3000-UNV3099
UNV3000E Job network creation failed: (msgNo) bapiStr
Description
An error occurred in the job network creation process. The error originated in a BAPI called on the SAP R/3 system. msgNo gives the BAPI message number. bapiStr gives information about the error, including the name of the BAPI that generated the error.
Severity
Error
System Action
The program terminates.
User Action
Check for additional messages issued by Universal Connector. The SAP R/3 syslog may contain additional information about the error.
Try to determine the cause of the error. If a cause cannot be found and the error condition persists, contact Stonebranch customer support.
Component
Universal Connector
UNV3001E Job network start failed: (msgNo) bapiStr
Description
An error occurred trying to start a job network. The error originated in a BAPI called on the SAP R/3 system. msgNo gives the BAPI message number. <->
bapiStr gives information about the error, including the name of the BAPI that generated the error.
Severity
Error
System Action
The program terminates.
User Action
Check for additional messages issued by Universal Connector. The SAP R/3 syslog may contain additional information about the error.
Try to determine the cause of the error. If a cause cannot be found and the error condition persists, contact Stonebranch customer support.
Component
Universal Connector
UNV3002E Mutually exclusive PURGE parameters specified.
Description
One or more conflicting parameters have been specified for the PURGE command. Each command group has a specific set of options that are available to it.
Severity
Error
System Action
The program terminates.
User Action
Determine which PURGE parameters do not belong. Remove the conflicting command options and reissue the command.
Component
Universal Connector
UNV3003I Job network (jobnetid) has been created.
Description
The Job network identified by jobnetid has been created.
Severity
Informational
System Action
The program continues.
User Action
None.
Component
Universal Connector
UNV3004I Job network (jobnetid) - process(jobnetprcid) has been started.
Description
The Job network process, identified by jobnetid and jobnetprcid, has been started.
Severity
Informational
System Action
The program continues.
User Action
None.
Component
Universal Connector
UNV3005I Job network (jobnetid) has been purged.
Description
The job network identified by jobnetid has been purged.
Severity
Informational
System Action
The program continues.
User Action
None.
Component
Universal Connector
UNV3006W "Continuing without the use of BANK_MAP_PROCFL_GET_NET_STAT."
Description
Usap is unable to use BAPI function module BANK_MAP_PROCFL_GET_NET_STAT to retrieve the status of the FS job network. Processing will continue by relying on the technical return codes of the network processes.
Severity
Warning
System Action
Usap will use continue to process the job network.
User Action
Apply the necessary fix to the SAP R/3 system to support BAPI function module BANK_MAP_PROCFL_GET_NET_STAT.
Component
Universal Connector
UNV3007W "Usap is unable to purge the FS job network."
Description
BANK_MAP_PROCFL_DESTRUCTOR is not available on the SAP R/3 system. Usap is unable to purge the FS job network.
Severity
Warning
System Action
Usap will use continue to process the job network.
User Action
Apply the necessary fix to the SAP R/3 system to support BAPI function module BANK_MAP_PROCFL_DESTRUCTOR.
Component
Universal Connector
UNV3008I Job network (netid) - process (netprocid): technical status is now (jobStatus).
Description
Indicates that the jobnet process' technical status has changed to jobStatus.
Severity
Informational
System Action
The program continues.
User Action
None.
Component
Universal Connector
UNV3009I Job network (netid) - process (netprocid): application status is now (jobStatus).
Description
Indicates that the jobnet process' application status has changed to jobStatus.
Severity
Informational
System Action
The program continues.
User Action
None.
Component
Universal Connector
UNV3010I Job network (netid) - process (netprocid): application status is now (jobStatus).
Description
Indicates that the jobnet process' application status has changed to jobStatus.
Severity
Informational
System Action
The program continues.
User Action
None.
Component
Universal Connector
UNV3011E A command ID must be specified when requesting a restart.
Description
When an attempt is made to restart a USAP started SAP R/3 job, a unique command ID must be supplied. This command ID is used by USAP to validate the restart request.
Severity
Error
System Action
The program terminates.
User Action
Add the -cmdid parameter to the USAP command line and specify the same command ID that was used for the initial run.
Component
Universal Connector
UNV3012E Unable to determine job name for restart option.
Description
A job name was not found on the command line or in a job definition file.
Severity
Error
System Action
The program terminates.
User Action
Make sure the job name is specified on the command line or, properly defined in a job definition file.
Component
Universal Connector
UNV3013E Job jobname/jobid already exists with Command ID (cmdId).
Description
A job with command ID cmdId already exists in the SAP R/3 system.
Severity
Error
System Action
The program terminates.
User Action
The pre-existing job with command ID cmdId must be removed from the R/3 system or, a unique jobname/command ID pair must be used.
Component
Universal Connector
UNV3014E Restart failed: Job (jobname) with command ID (cmdId) not found.
Description
Restart 'yes' was specified but, the restart job could not be found in the SAP R/3 system.
Severity
Error
System Action
The program terminates.
User Action
Make sure the job name and command ID are correct. If they are correct, the job must be defined to the R/3 system. This can be done automatically if the restart option is set to 'auto'.
Component
Universal Connector
UNV3015E Restart failed: multiple command ID jobs were found.
Description
Restart 'yes' was specified but, more than one job was found that matched the command ID job criteria.
Severity
Error
System Action
The program terminates.
User Action
Make sure the job name and command ID are correct. If they are correct, the duplicate command ID jobs must be purged from the R/3 system.
Component
Universal Connector
UNV3016I Starting search for command ID job: jobname/jobid/cmdid.
Description
Beginning a search for a command ID job.
Severity
Informational
System Action
The program continues.
User Action
Nothing.
Component
Universal Connector
UNV3017I Found command ID job: jobname/jobid/cmdid.
Description
A command ID job was found.
Severity
Informational
System Action
The program continues.
User Action
Nothing.
Component
Universal Connector
UNV3018I Ending search for command ID job: jobname/jobid/cmdid.
Description
The search for the command ID job has completed.
Severity
Informational
System Action
The program continues.
User Action
Nothing.
Component
Universal Connector
UNV3019E A command ID must be specified when requesting a restart.
Description
When an attempt is made to restart a Universal Connector command ID job, a unique command ID must be supplied. This command ID is used by the USAP to validate the restart request.
Severity
Error
System Action
The program terminates.
User Action
Add the -cmdid parameter to the Universal Connector command line and specify the same command ID that was used for the initial run.
Component
Universal Connector
UNV3020E Auto restart not allowed: auto_restart_ok option is set to NO.
Description
The AUTO option was specified for 'restart' parameter and the 'auto_restart_ok' parameter is set to NO.
Severity
Error
System Action
The program terminates.
User Action
Either set the auto_restart_ok parameter to YES or do not use the restart AUTO option.
Component
Universal Connector
UNV3021E 'Find Command ID Job' failed: (msgNo) bapiStr.
Description
An error occurred trying to find command ID jobs in the SAP R/3 system. The error originated in a BAPI called on the SAP R/3 system. msgNo gives the BAPI message number. bapiStr gives information about the error, including the name of the BAPI that generated the error.
This most likely does not indicate an error in processing. It usually indicates the absence of the job in the R/3 system.
Severity
Error
System Action
The program terminates.
User Action
Check for additional messages issued by Universal Connector. The SAP R/3 syslog may contain additional information about the error.
Try to determine the cause of the error. If a cause cannot be found and the error condition persists, contact Stonebranch customer support.
Component
Universal Connector
UNV3022I Reconnecting to command ID job: jobname/jobid/cmdid.
Description
A command ID job matching the criteria specified on the command line was found. USAP will reconnect to the SAP R/3 job and complete the tasks specified on the command line.
Severity
Informational
System Action
The program continues.
User Action
Nothing.
Component
Universal Connector
UNV3023I Creating command ID job: jobname/jobid/cmdid.
Description
A command ID job will be created in the SAP R/3 system.
Severity
Informational
System Action
The program continues.
User Action
Nothing.
Component
Universal Connector
UNV3024E Variant creation failed: (msgNo) bapiStr
Description
An error occurred in the variant creation process. The error originated in a BAPI called on the SAP R/3 system. msgNo gives the BAPI message number. bapiStr gives information about the error, including the name of the BAPI that generated the error.
Severity
Error
System Action
The program terminates.
User Action
Check for additional messages issued by Universal Connector. The SAP R/3 syslog may contain additional information about the error.
Try to determine the cause of the error. If a cause cannot be found and the error condition persists, contact Stonebranch customer support.
Component
Universal Connector
UNV3025E Obtaining variant contents failed: (msgNo) bapiStr
Description
An error occurred obtaining variant contents. The error originated in a BAPI called on the SAP R/3 system. msgNo gives the BAPI message number. bapiStr gives information about the error, including the name of the BAPI that generated the error.
Severity
Error
System Action
The program terminates.
User Action
Check for additional messages issued by Universal Connector. The SAP R/3 syslog may contain additional information about the error.
Try to determine the cause of the error. If a cause cannot be found and the error condition persists, contact Stonebranch customer support.
Component
Universal Connector
UNV3026E Invalid Generate command: disp.
Description
The command option, gen, entered for the GENERATE command is not valid.
Severity
Error
System Action
The program terminates.
User Action
Check the Universal Connector Reference Guide or command-line help for proper spelling and valid options.
Component
Universal Connector
UNV3027E Generating variant failed: (msgNo) bapiStr
Description
An error occurred trying to generate the variant. The error originated in a BAPI called on the SAP R/3 system. msgNo gives the BAPI message number. bapiStr gives information about the error, including the name of the BAPI that generated the error.
Severity
Error
System Action
The program terminates.
User Action
Check for additional messages issued by Universal Connector. The SAP R/3 syslog may contain additional information about the error.
Try to determine the cause of the error. If a cause cannot be found and the error condition persists, contact Stonebranch customer support.
Component
Universal Connector
UNV3028I Variant var was successfully created for report rpt.
Description
Indicates that the variant creation process was completed successfully for variant var of report rpt.
Severity
Informational
System Action
The program continues.
User Action
None.
Component
Universal Connector
UNV3029I Variant var was successfully modified for report rpt.
Description
Indicates that the variant modification process was completed successfully for variant var of report rpt.
Severity
Informational
System Action
The program continues.
User Action
None.
Component
Universal Connector
UNV3030I Variant var was successfully generated for report rpt.
Description
Indicates that the variant definition process was completed successfully for variant var of report rpt.
Severity
Informational
System Action
The program continues.
User Action
None.
Component
Universal Connector
UNV3031I Requesting interface: interface version.
Description
USAP is requesting the specified interface
Severity
Informational
System Action
The program continues.
User Action
None.
Component
Universal Connector
UNV3032I Using interface: interface version.
Description
Indicates that the variant definition process was completed successfully for variant var of report rpt.
Severity
Informational
System Action
The program continues.
User Action
None.
Component
Universal Connector
UNV3033E Job header modification failed: (msgNo) bapiStr
Description
An error occurred while attempting to modify the job header. The error originated in a BAPI called on the SAP R/3 system. msgNo gives the BAPI message number. bapiStr gives information about the error, including the name of the BAPI that generated the error.
Severity
Error
System Action
The program terminates.
User Action
Check for additional messages issued by Universal Connector. The SAP R/3 syslog may contain additional information about the error.
Try to determine the cause of the error. If a cause cannot be found and the error condition persists, contact Stonebranch customer support.
Component
Universal Connector
UNV3034E Command step modification failed: (msgNo) bapiStr
Description
An error occurred while attempting to modify a command step. The error originated in a BAPI called on the SAP R/3 system. msgNo gives the BAPI message number. bapiStr gives information about the error, including the name of the BAPI that generated the error.
Severity
Error
System Action
The program terminates.
User Action
Check for additional messages issued by Universal Connector. The SAP R/3 syslog may contain additional information about the error.
Try to determine the cause of the error. If a cause cannot be found and the error condition persists, contact Stonebranch customer support.
Component
Universal Connector
UNV3035I Job jobname/jobid was successfully created.
Description
Indicates that the job creation process was completed successfully for job jobname/jobid.
Severity
Informational
System Action
The program continues.
User Action
None.
Component
Universal Connector
UNV3036I Job jobname/jobid was successfully modified.
Description
Indicates that the job modification process was completed successfully for job jobname/jobid.
Severity
Informational
System Action
The program continues.
User Action
None.
Component
Universal Connector
UNV3037E Mutually exclusive RELEASE parameters specified.
Description
One or more conflicting parameters have been specified for the RELEASE command. Each command group has a specific set of options that are available to it.
Severity
Error
System Action
The program terminates.
User Action
Determine which RELEASE parameters do not belong. Remove the conflicting command options and reissue the command.
Component
Universal Connector
UNV3038E Job definition requires XBP 2.0 interface.
Description
The job definition file contains one or more keywords for parameters that can only be defined using the XBP 2.0 interface.
Severity
Error
System Action
The program terminates.
User Action
Remove the keywords that require the CM interface or, turn on auto CM.
Component
Universal Connector
UNV3039E External program step creation failed: (msgNo) bapiStr
Description
An error occurred adding a step to a job. The error originated in a BAPI called on the SAP R/3 system. msgNo gives the BAPI message number. bapiStr gives information about the error, including the name of the BAPI that generated the error.
Severity
Error
System Action
The program terminates.
User Action
Check for additional messages issued by Universal Connector. The SAP R/3 syslog may contain additional information about the error.
Try to determine the cause of the error. If a cause cannot be found and the error condition persists, contact Stonebranch customer support.
Component
Universal Connector
UNV3040E External command step creation failed: (msgNo) bapiStr
Description
An error occurred adding a step to a job. The error originated in a BAPI called on the SAP R/3 system. msgNo gives the BAPI message number. bapiStr gives information about the error, including the name of the BAPI that generated the error.
Severity
Error
System Action
The program terminates.
User Action
Check for additional messages issued by Universal Connector. The SAP R/3 syslog may contain additional information about the error.
Try to determine the cause of the error. If a cause cannot be found and the error condition persists, contact Stonebranch customer support.
Component
Universal Connector
UNV3041E Unknown step type: 'steptype'
Description
An unknown step type was encountered while generating a job definition.
Severity
Error
System Action
The program terminates.
User Action
Check for additional messages issued by Universal Connector. The SAP R/3 syslog may contain additional information about the error.
Try to determine the cause of the error. If a cause cannot be found and the error condition persists, contact Stonebranch customer support.
Component
Universal Connector
UNV3042I Job definition was successfully generated from job jobname/jobid.
Description
Indicates that the job definition generation process was completed successfully from job jobname/jobid.
Severity
Informational
System Action
The program continues.
User Action
None.
Component
Universal Connector
UNV3043I Job jobname/jobid was successfully purged from the system.
Description
Indicates that job jobname/jobid was successfully purged from the R/3 system.
Severity
Informational
System Action
The program continues.
User Action
None.
Component
Universal Connector
UNV3044I job status is now jobStatus.
Description
Indicates that the job status has changed to jobStatus.
Severity
Informational
System Action
The program continues.
User Action
None.
Component
Universal Connector
UNV3045I Detected child job jobname/jobid.
Description
Indicates that a child job jobname/jobid was detected.
Severity
Informational
System Action
The program continues.
User Action
None.
Component
Universal Connector
UNV3046E Missing job step.
Description
A job step was not defined for the job.
Severity
Error
System Action
The program continues.
User Action
None.
Component
Universal Connector
UNV3047I Intercept table was successfully replaced.
Description
The job intercept table was successfully replaced.
Severity
Informational
System Action
The program continues.
User Action
None.
Component
Universal Connector
UNV3048I Intercept table was successfully appended.
Description
The job intercept table was successfully appended.
Severity
Informational
System Action
The program continues.
User Action
None.
Component
Universal Connector
UNV3049E Syslog Read failed: (msgNo) bapiStr
Description
An error occurred trying to read the syslog. The error originated in a BAPI called on the SAP R/3 system. msgNo gives the BAPI message number. bapiStr gives information about the error, including the name of the BAPI that generated the error.
Severity
Error
System Action
The program terminates.
User Action
Check for additional messages issued by Universal Connector. The SAP R/3 syslog may contain additional information about the error.
Try to determine the cause of the error. If a cause cannot be found and the error condition persists, contact Stonebranch customer support.
Component
Universal Connector
UNV3050E Job intercept table modification failed: (msgNo) bapiStr
Description
An error occurred in the job intercept table modification process. The error originated in a BAPI called on the SAP R/3 system. msgNo gives the BAPI message number. bapiStr gives information about the error, including the name of the BAPI that generated the error.
Severity
Error
System Action
The program terminates.
User Action
Check for additional messages issued by Universal Connector. The SAP R/3 syslog may contain additional information about the error.
Try to determine the cause of the error. If a cause cannot be found and the error condition persists, contact Stonebranch customer support.
Component
Universal Connector
UNV3051E Get remote system time failed: (msgNo) bapiStr
Description
An error occurred getting the remote system time. At this point, Universal Connector is logging on to the SAP R/3 system. The error originated in a BAPI called on the SAP R/3 system. msgNo gives the BAPI message number. bapiStr gives information about the error, including the name of the BAPI that generated the error.
Severity
Error
System Action
The program terminates.
User Action
Check for additional messages issued by Universal Connector. The SAP R/3 syslog may contain additional information about the error.
Try to determine the cause of the error. If a cause cannot be found and the error condition persists, contact Stonebranch customer support.
Component
Universal Connector
UNV3052E Raise background processing event failed: (msgNo) bapiStr
Description
An error occurred trying raise the background processing event. The error originated in a BAPI called on the SAP R/3 system. msgNo gives the BAPI message number. bapiStr gives information about the error, including the name of the BAPI that generated the error.
Severity
Error
System Action
The program terminates.
User Action
Check for additional messages issued by Universal Connector. The SAP R/3 syslog may contain additional information about the error.
Try to determine the cause of the error. If a cause cannot be found and the error condition persists, contact Stonebranch customer support.
Component
Universal Connector
UNV3053E Error in RAISE_BP_EVENT command: Mutually exclusive options specified.
Description
The options specified with the RAISE_BP_EVENT command indicate using both usap definition file and command line event options for the RAISE_BP_EVENT. These two options are mutually exclusive.
Severity
Error
System Action
The program terminates.
User Action
Determine which source was intended for the SUBMIT command, emit the conflicting information, and reissue the command.
Component
Universal Connector
UNV3054I Background processing event event_id "event_parm" was successfully raised.
Description
Indicates that the background processing event was successfully raised in the SAP R/3 system.
Severity
Informational
System Action
The program continues.
User Action
None.
Component
Universal Connector
UNV3055E Display reports failed: (msgNo) bapiStr
Description
An error occurred retrieving the list of reports. The error originated in a BAPI called on the SAP R/3 system. msgNo gives the BAPI message number. bapiStr gives information about the error, including the name of the BAPI that generated the error.
Severity
Error
System Action
The program terminates.
User Action
Check for additional messages issued by Universal Connector. The SAP R/3 syslog may contain additional information about the error.
Try to determine the cause of the error. If a cause cannot be found and the error condition persists, contact Stonebranch customer support.
Component
Universal Connector
UNV3056E Display external commands failed: (msgNo) bapiStr
Description
An error occurred retrieving the list of external commands. The error originated in a BAPI called on the SAP R/3 system. msgNo gives the BAPI message number. bapiStr gives information about the error, including the name of the BAPI that generated the error.
Severity
Error
System Action
The program terminates.
User Action
Check for additional messages issued by Universal Connector. The SAP R/3 syslog may contain additional information about the error.
Try to determine the cause of the error. If a cause cannot be found and the error condition persists, contact Stonebranch customer support.
Component
Universal Connector
UNV3057E Display output devices failed: (msgNo) bapiStr
Description
An error occurred retrieving the list of output devices. The error originated in a BAPI called on the SAP R/3 system. msgNo gives the BAPI message number. bapiStr gives information about the error, including the name of the BAPI that generated the error.
Severity
Error
System Action
The program terminates.
User Action
Check for additional messages issued by Universal Connector. The SAP R/3 syslog may contain additional information about the error.
Try to determine the cause of the error. If a cause cannot be found and the error condition persists, contact Stonebranch customer support.
Component
Universal Connector
UNV3058E Display print format failed: (msgNo) bapiStr
Description
An error occurred retrieving the list of print formats. The error originated in a BAPI called on the SAP R/3 system. msgNo gives the BAPI message number. bapiStr gives information about the error, including the name of the BAPI that generated the error.
Severity
Error
System Action
The program terminates.
User Action
Check for additional messages issued by Universal Connector. The SAP R/3 syslog may contain additional information about the error.
Try to determine the cause of the error. If a cause cannot be found and the error condition persists, contact Stonebranch customer support.
Component
Universal Connector
UNV3059E Job release failed: (msgNo) bapiStr
Description
An error occurred trying to release a job. The error originated in a BAPI called on the SAP R/3 system. msgNo gives the BAPI message number. <->
bapiStr gives information about the error, including the name of the BAPI that generated the error.
Severity
Error
System Action
The program terminates.
User Action
Check for additional messages issued by Universal Connector. The SAP R/3 syslog may contain additional information about the error.
Try to determine the cause of the error. If a cause cannot be found and the error condition persists, contact Stonebranch customer support.
Component
Universal Connector
UNV3060E Display criteria table failed: (msgNo) bapiStr
Description
An error occurred trying to read the intercept criteria table. The error originated in a BAPI called on the SAP R/3 system. msgNo gives the BAPI message number. bapiStr gives information about the error, including the name of the BAPI that generated the error.
Severity
Error
System Action
The program terminates.
User Action
Check for additional messages issued by Universal Connector. The SAP R/3 syslog may contain additional information about the error.
Try to determine the cause of the error. If a cause cannot be found and the error condition persists, contact Stonebranch customer support.
Component
Universal Connector
UNV3061E Display intercepted jobs failed: (msgNo) bapiStr
Description
An error occurred trying to retrieve intercepted jobs. The error originated in a BAPI called on the SAP R/3 system. msgNo gives the BAPI message number. bapiStr gives information about the error, including the name of the BAPI that generated the error.
Severity
Error
System Action
The program terminates.
User Action
Check for additional messages issued by Universal Connector. The SAP R/3 syslog may contain additional information about the error.
Try to determine the cause of the error. If a cause cannot be found and the error condition persists, contact Stonebranch customer support.
Component
Universal Connector
UNV3062E Initialization failed: func, errno, reason
Description
The component configuration information provided by Universal Broker and required by UCMD Server to establish its runtime environment could not be processed. func is the name of the function in which the error occurred. errno is the error number. reason is an explanation of the error.
Severity
Error
System Action
The program terminates.
User Action
Contact Stonebranch customer support.
Component
Universal Connector
UNV3063I Trace data set is 'dsn, volser'.
Description
Universal Connector was started with a message level of TRACE, which may result in an application trace being written. The trace data set is dsn on volume volser.
Severity
Informational
System Action
The program continues.
User Action
No action required.
Component
Universal Connector
UNV3064W Job log exceeds user specified maximum size limit of (max_joblog_size).
Description
The SAP job log for the current job exceeds the user specified maximum log size. Therefore, USAP will not attempt to retrieve the job log. The job log will be left on the SAP R/3 system. This message is followed by additional messages that provide information about the job log.
Severity
Warning
System Action
The program continues.
User Action
No action required.
Component
Universal Connector
UNV3065I Job.....................: jobname/jobid
Description
Displays the current job name and number.
Severity
Informational
System Action
The program continues.
User Action
No action required.
Component
Universal Connector
UNV3066I TemSe object name.......: name
Description
Displays the SAP R/3 TemSe object name that contains the job log.
Severity
Informational
System Action
The program continues.
User Action
No action required.
Component
Universal Connector
UNV3067I SAP R/3 client..........: name
Description
Displays the SAP R/3 client, in which the job log was created.
Severity
Informational
System Action
The program continues.
User Action
No action required.
Component
Universal Connector
UNV3068I Size of job log.........: size bytes
Description
Displays the size of the job log in bytes.
Severity
Informational
System Action
The program continues.
User Action
No action required.
Component
Universal Connector
UNV3069W Spool list request exceeds user specified maximum size limit of (max_spool_size).
Description
A spoollist on the SAP R/3 system that was targeted for retrieval by the current USAP command invocation exceeds the user specified maximum spool size. Therefore, USAP will not attempt to retrieve the spoollist. The spoollist will be left on the SAP R/3 system. This message is followed by additional messages that provide information about the spoollist.
Severity
Warning
System Action
The program continues.
User Action
No action required.
Component
Universal Connector
UNV3070I Job.....................: jobname/jobid
Description
Displays the current job name and number.
Severity
Informational
System Action
The program continues.
User Action
No action required.
Component
Universal Connector
UNV3071I Step....................: stepnumber
Description
Displays the current job step number.
Severity
Informational
System Action
The program continues.
User Action
No action required.
Component
Universal Connector
UNV3072I Spool request number....: spoolnumber
Description
Displays the spoollist request number.
Severity
Informational
System Action
The program continues.
User Action
No action required.
Component
Universal Connector
UNV3073I Spool pages.............: pages
Description
Displays the number of pages in the spoollist.
Severity
Informational
System Action
The program continues.
User Action
No action required.
Component
Universal Connector
UNV3074I Spool Size..............:title
Description
Displays the spoollist size in bytes.
Severity
Informational
System Action
The program continues.
User Action
No action required.
Component
Universal Connector
UNV3075I Spool title.............: title
Description
Displays the spoollist title.
Severity
Informational
System Action
The program continues.
User Action
No action required.
Component
Universal Connector
UNV3078E [Line: lineNum] Invalid SELNAME value value for variant varName."
Description
A SELNAME value specified in the variant definition file at line lineNum is not valid for the variant being defined.
Value is the invalid value. varName is the variant that is being defined.
Severity
Error
System Action
The program terminates.
User Action
Correct the SELNAME value in the USAP variant definition file. The value must be a valid variant parameter name for the SAP ABAP report that the variant is being defined for.
Component
Universal Connector
UNV3079I Performing secondary uniqueness test for command ID job: jobname/jobid/cmdid.
Description
Beginning a secondary uniqueness test for a command ID job. The secondary test is required to deal with race conditions that can occur if multiple command ID jobs are submitted simultaneously with the same command ID.
Severity
Informational
System Action
The program continues.
User Action
Nothing.
Component
Universal Connector
UNV3080E Error initializing local Broker interface: func, errno, reason
Description
An error occurred initializing the interface to the local Universal <->
Broker. The manager communicates with the local Broker to register with it and to obtain its configuration data. The function func failed with an error code of errno, which is described by reason.
Severity
Error
System Action
The process terminates.
User Action
Check that a local Broker is running on the same system as the manager. If a Broker is not running, one must be started prior to starting the manager. Contact Stonebranch Customer Support is assistance is needed.
Component
Universal Connector
UNV3081E Error recording process exit code: func, errno, reason
Description
An error occurred recording the manager process exit code for local Broker monitoring. The function func failed with an error code of errno, which is described by reason.
Severity
Error
System Action
The manager terminates. The local Broker shall detect that the manager ended, but it will not know the manager exit conditions.
User Action
On UNIX, the process lock file (PLF) used by the manager may have been corrupted or removed. Although the condition cannot be recovered, the cause of the problem should be determined to prevent it from reoccurring. Contact Stonebranch Customer Support is assistance is needed.
Component
Universal Connector
UNV3082E Error registering with local Broker: func, errno, reason
Description
An error occurred registering with the local Universal Broker. The registration process is required for the manager to obtain its configuration data from the local Broker. The function func failed with an error code of errno, which is described by reason.
Severity
Error
System Action
The manager terminates.
User Action
Check that a local Broker is running on the same system as the manager. If a Broker is not running, one must be started prior to starting the manager. Contact Stonebranch Customer Support is assistance is needed.
Component
Universal Connector
UNV3083E Error establishing local broker session: func, errno, reason
Description
An error occurred establishing a communication session with the local broker. The function that failed is identified by field 'func'. Field p>errno is the error number, and field reason is an explanation of the error.
Severity
Error
System Action
The program terminates.
User Action
Contact Stonebranch customer support if unable to identify and resolve the problem.
Component
Universal Connector
UNV3084E Error initializing local Broker interface using system ID 'sid': func, errno, reason
Description
An error occurred initializing the interface to the local Universal Broker using system identifier sid. The manager communicates with the local Broker to register with it and to obtain its configuration data. The function func failed with an error code of errno, which is described by reason.
Severity
Error
System Action
The process terminates.
User Action
Check that a local Broker is running with the appropriate system ID on the same system as the manager. If a Broker is not running, one must be started prior to starting the manager. Contact Stonebranch Customer Support is assistance is needed.
Component
Universal Connector
UNV3085E Error in caller provided UUID: func, errno, reason
Description
The process and group UUID values provided by the calling process could not be successfully processed. An error was encountered by function func. The error number is errno and a description of the error is reason.
Severity
Error
System Action
The program terminates.
User Action
Contact Stonebranch customer support if unable to identify and resolve the problem.
Component
Universal Connector
UNV3086E Error initializing for event generation: func, errno, reason.
Description
An error occurred initializing for event generation. The function that encountered the error is func. The error number returned is errno. An explanation of the error is reason.
Severity
Error
System Action
The program terminates.
User Action
Report the error to Stonebranch Customer Support.
Component
Universal Connector
UNV3087I Universal Connector component cid registered with local Broker 'sid'.
Description
The connector has successfully registered with the local Broker. The connector has been assigned component ID cid by the Broker. If multiple Brokers are supported by the O/S, the system ID of the Broker is identified by sid.
Severity
Informational
System Action
Processing continues.
User Action
None required.
Component
Universal Connector
UNV3088E Failed initializing Component Instance: func, errno, reason
Description
The component configuration information provided by Universal Broker and required by USAP to establish its runtime environment could not be processed. func is the name of the function in which the error occurred. errno is the error number. reason is an explanation of the error.
Severity
Error
System Action
The program terminates.
User Action
Contact Stonebranch customer support.
Component
Universal Connector
UNV3089I Job jobname/jobid was successfully aborted.
Description
Indicates that job jobname/jobid was successfully Aborted.
Severity
Informational
System Action
The program continues.
User Action
None.
Component
Universal Connector
UNV3090A Configuration information:
Description
A header that precedes the display of configuration options in effect for the Universal Connector.
Severity
Audit
System Action
None.
User Action
None required.
Component
Universal Connector
UNV3091A config options:
Description
A header that precedes the display of specific configuration options in effect for the Universal Connector. config is the category of options being displayed.
Severity
Audit
System Action
None.
User Action
None required.
Component
Universal Connector
UNV3092A System identifier: sid
Description
Displays the system identifier of the local Broker to which the connecter will register.
Severity
Audit
System Action
None.
User Action
None required.
Component
Universal Connector
UNV3093A Broker interface file directory: bifdir
Description
Displays the directory in which the connector searches for the local broker interface file.
Severity
Audit
System Action
None.
User Action
None required.
Component
Universal Connector
UNV3094A Process lock file directory: bifdir
Description
Displays the directory in which the connector creates its process lock file used by the local Broker to monitor the connector.
Severity
Audit
System Action
None.
User Action
None required.
Component
Universal Connector
UNV3095A Destination: dest
Description
Displays the destination in the SAPRFC.INI file that will be used to connect to the SAP system.
Severity
Audit
System Action
None.
User Action
None required.
Component
Universal Connector
UNV3096A ASHOST: ashost
Description
Displays the Application Server Host string that will be used to connect to the SAP system.
Severity
Audit
System Action
None.
User Action
None required.
Component
Universal Connector
UNV3097A System Number: sysnr
Description
Displays the SAP system number that will be used to connect to the SAP system.
Severity
Audit
System Action
None.
User Action
None required.
Component
Universal Connector
UNV3098A Client Number: client
Description
Displays the SAP client number that will be used to connect to the SAP system.
Severity
Audit
System Action
None.
User Action
None required.
Component
Universal Connector
UNV3099A SAP logon language: saplang
Description
Displays the SAP logon language that will be used for the RFC session.
Severity
Audit
System Action
None.
User Action
None required.
Component
Universal Connector